Learning how to navigate a boat is one of the most important things any boat owner must learn. Essentially, nautical navigation is no more than knowing how to get from Point A to Point B. But the process can be a whole lot more challenging than simply pointing the bow in the right direction.

Everyone, of course, is more or less familiar with some form of navigation. Itā€™s what you do every time you travel, whether youā€™re jogging through a park or driving into town. But on the water, navigation takes on a new level of complexity. First off, there are no roads to follow. Secondly, visibility may be restricted by fog, rain, haze, and darkness. And thirdly, paths that appear to be safe to the naked eye may in fact be filled with hards such as shallow zones, underwater obstructions, piers or pilings, commercial fishing gear, and more. So, how will you navigate through these treacherous waters? Weā€™ll take a close look at two methods: traditional navigation and electronic navigation.

Fairline Targa 65 GT Exterior

Can you safely steer your boat from here, to there? Knowing how to navigate is a must. Image credit: Fairline Targa 65 GT Exterior



Traditional Navigation


Just a few short decades ago we didnā€™t have electronics like GPS and chartplotters. And going back for thousands of years, mariners have been studying how to safely get across rivers, bays, and oceans. No matter where youā€™re navigating or what type of boat youā€™re on, the number-one tool you use while navigating is your own eyes. Beyond that, standard navigation tools include:

  • A compass and/or hand bearing compass: A compass tells you which direction your boat is heading in, north, south, east, or west, as measured in degrees relative to magnetic north. There are 360 degrees representing a full circle, with 0 degrees to the north, 180 degrees to the south, 90 degrees to the east, and 270 degrees to the west. A hand-bearing compass can be utilized to quickly take multiple ā€œbearingsā€ (the direction of a course, or the direction to an item or place) of multiple visible landmarks.

  • Charts: Charts are nautical maps. NOAA (the National Oceanic and Atmospheric Association) produces charts of navigable US waterways, as well as many international charts. You can buy NOAA charts or view them online for free.

  • Parallel Rules: These are a set of two rulers which are attached by swiveling arms. The arms allow you to open and close the rulers, ā€œwalkingā€ them across a chart, while maintaining the same angle.

  • Dividers: This tool (also sometimes called ā€œcompass dividersā€) is used to measure distance on a chart. You can separate its two points more or less, to represent a nautical mile or a number of miles.

  • An erasable pencil: A pencil is needed for navigation via chart so you can mark down important items like speed, location, and bearings.

  • A wristwatch or stopwatch: In order to perform one of the most basic forms of navigationā€”ded reckoning (or "deduced reckoning"), which weā€™ll talk more about in a momentā€”you need to keep track of time.


Some calculations can be made more easily with items like a nautical slide rule or a protractor, but the above list covers the absolute necessities for basic nautical navigation.

The basic tools of navigation, from left to right at top, a compass, a chart, parallel rules; and at bottom, dividers, and a stopwatch.

So, just how do you use these tools while getting from Point A to Point B? Some of the basic things youā€™ll need to do to navigate your boat:

  • Locate your position

  • Create a route with bearings

  • Determine a reciprocal course

  • Plot your position with Ded Reckoning


Locating Your Position:


Sometimes you can simply look at your surroundings, glance at the chart, and youā€™ll know where you are. Say for example that youā€™re next to a big red buoy with the number five on it, and when you look on the chart you see the red number five buoy front and center. Position acquired. But locating your position may be easier said than done, especially in unfamiliar waters. One of the most basic (and best) ways to accomplish this feat is triangulation. In order to triangulate your position youā€™ll need to identify three visible landmarks or aids to navigation that are clearly marked on your chart, and are relatively far apart from each other (the farther, the more accurate your calculation will be). Lighthouses, points of land, water or radio towers, and navigational markers are prime examples.

First, use your hand-bearing compass to ā€œshootā€ a bearing to the first landmark (or, if you only have the compass mounted at your helm, point the entire boat directly at it to acquire the bearing). Line up your parallel rules on the chartā€™s compass rose (the illustrated circle marked with degrees) to match the degree of the bearing you shot. Note that there are two circles of degrees on the rose, one (the outer ring) representing true north and the other (the inner ring) representing magnetic north. Use the inner magnetic ring, because your compass points to magnetic north, not true north. Then, walk the rules across the chart by holding down one side and moving the other towards your landmark, one after the other. When an edge of your parallel rule intersects with the landmark, use your pencil to trace a line down the ruleā€™s edge.

Now, repeat the process with the other two landmarks. If the three lines youā€™ve drawn intersect, you now know exactly where you are on the chart. If they come close and create a triangle, youā€™re somewhere inside that triangle. You can get a more exact location by adding more landmarks and bearings, or by taking more accurate bearings.

Watch our Basic Boat Navigation: How to Triangulate Your Position Video.

Advertisement


Create a Route with Bearings:


Whether youā€™re planning a trip or youā€™re already on the water, youā€™ll need to know how to create a route. And unless youā€™re lucky enough to be going in a straight line with no obstructions in the way or channels to follow, that route will require multiple different bearings. Fortunately, this is an extremely easy process. Simply lay your parallel rules at your starting point, line the edge along the path you want to cruise, and draw a straight line on your chart. Then walk the rules until the edge intersects with the center of the compass rose, to get the bearing that corresponds with the line. Jot down the bearing next to the line, and youā€™ve created the first leg of your journey. Lay the parallel rules along the next leg, and repeat the process. And so on, until you create the final leg that intersects with your destination. When you cruise along each leg, youā€™ll know by glancing at the chart what bearing your compass should show.

Watch our Basic Boat Navigation: Creating a Route with Bearings to Navigate By Video.

Determine a Reciprocal Course:


This is one of the simpler navigation tasks, but itā€™s also quite important. If you donā€™t know your reciprocal (reverse) course, you canā€™t go back the way you came. Since your compass has 360 degrees, the reciprocal of whatever course youā€™re on will always be 180 degrees away. If the initial course is less than 180 degrees, add 180 to get the reciprocal. If itā€™s more than 180 degrees, subtract 180 to get the reciprocal.

Ded Reckoning:


This is a method of navigating from a known position to another position, using the information available to you, to deduce your approximate location. You need to know your speed, compass course, and the amount of time you travel, and record them all on your chart at every course change. If possible, you should include estimates of the effects of wind and current.

Here are the basic equations youā€™ll need to know:

  • Speed x Time = Distance

  • Distance / Speed = Time

  • Distance / Time = Speed


WARNING: Never mix up MPH and nautical miles per hour, or knots. Mathematically you can use either when making these calculationsā€”but not both. Since nautical charts measure distance in nautical miles (which equal 1.15 ā€œstatute,ā€ or regular miles) itā€™s always best to stick with knots and nautical miles (NM) when navigating a boat with traditional means.

Letā€™s say your boat cruises at 20 knots, to keep the math simple. And letā€™s say you know youā€™re at position X at high noon, when a light fog rolls in. You can still see well enough to continue on your cruise at 20 knots, but visibility is limited to a couple of miles and your familiar landmarks are now out of sight. On your chart, you create a route home that calls for a five NM leg on a bearing of 200 degrees, and a second 10 NM leg on a bearing of 250 degrees. Divide five (distance) by 20 (speed) to get 0.25, which tells you that youā€™ll need to cruise for a quarter of an hour at 200 degrees. You use your watch or stopwatch to keep track of time, and at 12:15, stop the boat. Now record the time and your estimated position. Then turn to 250 degrees, draw your next course line, and again record your speed and bearing. Now youā€™ll need to divide 10 by 20, and youā€™ll know that you should reach your destination in half an hour.

Some people may find it easier to calculate how many minutes it takes to travel a nautical mile at your given speed and use that figure to navigate. That 20-knot cruise will take you one NM every three minutes, for example (60 divided by 20), so you can make the same calculations knowing that it will take you 15 minutes (three times five), or a quarter of an hour, to go five NM.

Ded reckoning can also be used to track your position as you travel an undetermined route in conditions of reduced visibility. Letā€™s say youā€™re heading on a compass course of 180 degrees when you leave the harbor. When your watch or stopwatch says 15 minutes have passed, you change course to 220 degrees. Record your bearing, speed, and time of course change. 15 minutes later, you can make a fairly good guess at your positionā€”and keep track of your position as you cruise and make additional course or speed changes.

As long as you know the time, your boatā€™s speed, and its course, ded reckoning will allow you to keep track of your estimated position on a chart.

Ded reckoning is not, of course, an exact method. The ability of a helmsman to hold a steady course, wind and seas, and currents will all have an effect on how closely ded reckoning does or does not reflect your exact position at any given time. Cumulatively over long distances, little errors add up to become significant.

Watch our Basic Navigation: How to Navigate by Ded Reckoning video.

Once you have all these skills down-pat, you can get pretty much anywhere with your compass and basic navigational tools.

WARNING: all compasses are subject to magnetic interference, called ā€œdeviationā€. Before any accurate navigation can take place, refer to the installation guide that came with your compass and ā€œcompensateā€ it (set it to account for deviation). If you donā€™t have an installation guide handy, Google can help.

Electronic Navigation


electronic-navigation

A full suite of marine electronics makes navigation faster, easier, and far more accurate. Image credit: Neil Rabinowitz


Every mariner should understand basic traditional navigation, because you never know when your electronics will fail you. But truth be told, the vast majority of todayā€™s boaters will almost always do their navigation on an LCD screen. The good news? Electronic navigation is far, far easier than using traditional methods. Thereā€™s bad news, too: those electronics can cost big bucks. When considering navigational marine electronics, youā€™ll need to choose among the following:

  • AIS ā€“ Automatic Identification Systems are transmitters and/or receivers that identify most commercial ships and boats. Theyā€™re important for navigation because they can expose unseen dangers that lie along your course line, such as tugs and barges that are around the next bend of the river. Even if you donā€™t have an AIS system, when youā€™re within cell range you can access much of the information provided by AIS using an app like Shipfinder on your cell phone.

  • Chartplotter ā€“ For the vast majority of us, this is the most important electronic nav unit. It provides you with a digital chart that can be used for everything from plotting a course to getting a fix on your current location.

  • Fishfinder/depthsounder ā€“ Although depth soundings are on the digital charts used by chartplotters, they arenā€™t always accurate. Plus, depth can change with the tides or a lake or riverā€™s changing water levels. So a depth sounder becomes invaluable when navigating through waters that may not provide sufficient draft for your boat.

  • MFDs ā€“ Multifunction displays are informational hubs that sit at your helm, and can integrate all of the electronic units listed here onto one LCD screen.

  • Radar ā€“ Radar broadcasts pulses which are reflected by solid items that may be beyond visual range, like distant ships or land. Essentially, radar gives you electronic eyes that can see for dozens of miles beyond the visible horizon.


Most boaters don't need all of these units. On most inland lakes, for example, radar and AIS arenā€™t exactly necessities. So, how will you know which unit(s) are appropriate for the type of boating you do? We thoroughly addressed this question, in Marine Electronics.

Chartplotters


Chartplotters (and/or MFDs with chartplotting functions) are the number-one most useful electronic navigational tool, forming the basic building block of all electronic nav systemsā€”every mariner should have one at the helm.

Letā€™s take a closer look at this little magical box of tricks in specific. It allows you to perform those key navigational tasks we identified earlierā€”locating your position, creating routes and bearings, and determining reciprocal courses. And it makes ded reckoning obsolete, since you always know where you are at a glance. Its digital maps, called ā€œchartographyā€ in nautical parlance, can be more or less detailed depending on quality and cost. Most are based on the data originally gathered by NOAA and/or by private services, and can be updated or geographically expanded either by adding a chart data card or by using a WiFi link. Many of the latest units can even be updated in real time using the data gathered by your depth sounder and GPS. To learn more about the latest in marine chartography, read Chart Transplant. And to see how a chartography update works, watch Boating Tips: Chartography and Software Updates for Chartplotters.

Locating your position on a chartplotter is as easy as looking for the boat icon on the LCD screen. It will be clearly visible on the digital map, with the exact latitude and longitude identified via the unitā€™s GPS receiver, and displayed somewhere on-screen. Itā€™s as simple as that.

To create a route on a chartplotter, move the cursor to the position you want to go to, and press a button to create a waypoint. In the case of many touch-screen units, instead of pressing a button youā€™ll merely tap the screen. Press a ā€œgo toā€ button, and your bearing to that waypoint will be displayed. Turning the waypoint into a route is as easy as making more waypoints, or in some cases, pressing a ā€œrouteā€ button so the unit automatically joins multiple waypoints together into a route. In most cases, your chartplotter will offer a steering screen that displays a digital compass or numerically displays your bearing, course, and other important information like time to destination, speed, and course error.

Determining a reciprocal course with a chartplotter is as simple as highlighting the waypoint you need to return to, and pressing that ā€œgo toā€ button once more.

It will, of course, take a bit of practice to learn which buttons to press when, and how your chartplotter model in specific works. But we can help shorten the learning curveā€”watch our How-To Special: Basic Chartplotter Navigation video to see how itā€™s done before you try using the chartplotter at your helm.

What about all those other electronic navigational aids? Weā€™ve got you covered there, too. Check out these articles and videos, to learn the basics for each:

Once youā€™ve got the basics under your belt, view these more advanced articles and videos which will help a navigational novice step up his or her game:

Is this a lot of information to absorb? You bet. Will getting used to both traditional and electronic navigation techniques require some practice and real-world experience? Absolutely. But armed with all of this knowledge, your basic navigational tools, and your electronics, you should have no problem navigating your boat from Point A to Point Bā€”even in fog, rain, and darkness.

Editor's Note: This article was originally published August 2016, updated in June 2020 and March 2022.

Written by: Lenny Rudow
With over two decades of experience in marine journalism, Lenny Rudow has contributed to publications including YachtWorld, boats.com, Boating Magazine, Marlin Magazine, Boating World, Saltwater Sportsman, Texas Fish & Game, and many others. Lenny is a graduate of the Westlawn School of Yacht Design, and he has won numerous BWI and OWAA writing awards.
Advertisement