Machinery

• Twin main engines: Cummins QSM 11, 715 BHP 

• ZF335 IV with 2.458: 1 reduction x 2

• Engine instrument panel: Digital with instrumentation for oil pressure, water temperature, voltage, RPM, hour meter, with alarms

• Engine controls: CMD DTS

• Heat exchanger cooling

• Propeller shafts:  2.75″ (6.99 cm) A22HS

• Taper details: Standard S.A.E. taper

• Propeller nuts to be bronze

• Propellers: Hungshen 4-bladed bronze, 32″ diameter x 38″ pitch (81.28 cm d x 96.52 cm p) counter rotating

• Shaft Struts: Custom cast bronze per PAE design

• Stern tubes:

• Fiberglass

• Stuffing Boxes: PYI drip less shaft seals Model #02-234-414 (4 1/4″ – 4 3/8″ stern tube diameter)

• Fuel filters: Racor #900MA with vacuum gauges plus engine mounted filter x two (2)

• Wet Exhaust 

• “Marine Exhaust Systems” riser and muffler x two (2)

• Trident #252V blue exhaust hose with dual “T” clamps at each connection

• FRP tail pipe to transom

• Groco intake strainers to suit engine requirements x two (2)

• Engine cooling system to be filled with suitable mixture of coolant/antifreeze to insure coolant does not freeze for winter shipment

• Engine room floors: Fiberglass with non-skid – no wood structure used within engine room

• Engine room finish: Light Gray molded fiberglass with non-skid finish and insulated with Technitron or equivalent fire proof foiled and leaded foam 2″ (5.08 cm) thick.  All exposed insulated surfaces to be lined with perforated anodized aluminum sheets

• Engine room blowers:  Livos Technology model #FD-110 axial fans 24vdc 11″. Three (3) total blower fans; two (2) intakes and one (1) exhaust. Each blower to be controlled by a rheostat to allow for reversible operation. Reversible blower operation will allow the operator to select which side intakes and which side exhaustsdepending on weather and seaconditions.    

• Livos Technology moisture eliminators for two engine

• room vents. 9″h x 48″l located on hull sides

• Livos Technology moisture eliminator for exhaust vent on aft deck bulkhead 20″h x 12″w

• Bow thruster: Side Power 24volt model #SEP210/250TC, #SM10010 10″ (30.5cm) GRP bow tunnel, #SMPJC211 proportional panel controls x 2.

• Dual station controls one at lower helm and one at fly bridge

• Two of the eight house batteries to be located in the fwd bilge compartment this will give power to the thruster as well as the windlass

• All necessary fuses and switches

• Trim tabs: Bennett Premium BXT system

Carbon Xintex CO2 battery powered detector installed.

• AC Generator  (located in E/R)

• 21.5kw Onan with sound shield and gen-sep exhaust

• Racor #500MA fuel filter

• Generator digital display to located on the dash at the helm 

Structure

• Builder to utilize the latest vacuum bagging and resin infusion techniques on all main structures in order to save weight and increase strength.

• Hull lamination schedule with cored top sides per construction plan

• Vinyl ester resin used in first 3 layers of lamination

• All exterior gel coat to be CCP on superstructure and on hull and non-skid or equivalent high end gel coat.

• Deck lamination schedule per construction plan

Core: 

• Cabin side (vertical surfaces): Foam Gurit-G80 or equivalent cross-linked foam

• Cabin top and deck (horizontal surfaces): Gurit cross linked foam per construction plan

• Hull : Gurit cross linked foam per hull construction plan

• In way of all hardware installations the core-cell to be replaced with plywood

• Structural bulkheads to use Gurit foam

Deck/hull joint: 

• Between deck and hull flange: 3M 5200

• Inside of joint:  Two (2) layers mat and woven roving

• Mechanical fastening: 1/4″ (6mm) self tapping screws on 6″ (15 cm) centers. 

Longitudinal Stringer:

• Hull: Per hull construction plans

• Deck: Per deck construction plans

Interior floors: Honeycomb cored FRP per construction plans

Gel coat Color (standard boat):

• Hull: Arocoat #340 Light Gray

• Deck: Ferro White (GV48001)

• Non-skid: Arocoat #A139 Light Gray

• Boot-top and stack stripes: Arocoat #348 Dark Blue

Bottom Paint (Black) 

• 5 coats Petit Protect epoxy barrier coat

• 3 coats of Petit Trinidad SR anti-fouling paint

Interior Finish/Equipment

General

• Joinery work to be quarter sawn horizontal grain teak veneer with 7617 style joiner work with square moldings, door frames and fiddles.

• Wall covering and moldings located as per drawings

• All varnished surfaces to have a 60% gloss finish

• Interior cabinetry to be built using light weight plywood

• Hanging lockers to be lined with cedar or equivalent aromatic wood

• All locker doors and drawers to have Timage square body round push button latches

• Interior door lock sets to be Mobella “McCoy Star Square” door handles with privacy locks

• Interior cabin doors to have rubber gaskets for sound reduction and magnetic hold open catches

Galley

• Refrigerator: One (1) Bosch 800 series stainless steel model #B22CS80SS side by side.

• Countertops: Formica brand solid surface ‘Frost’ #102 – 1 1/2″ thick at edges squared edge detail with 3/4″ overlap to cabinet face below

• Flooring: Solid 2″ (5.08cm) wide teak planking

• Cabinetry/paneling: Teak with a 60% gloss varnish

• Stove: GE Café Series 30″ electric cook top #P350STSS GE Stove.jpg

• Oven: GE Café Series 30″ convection wall oven # CT918STSS

• Microwave: GE Café Series #CSA1201RSS, Convection with exhaust blower installed over stove.

• Overhead: Individual padded Majilite panels secured in place using the FastMount system for easy removal and reinstallation

• Locker interior finish: White Formica except inside fridge/freezer opening which will be teak

• Dish washer: GE Café Series # CDT765SSFSS

• Overhead galley locker as shown on plans

• Pull-out shelving unit in locker next to refer. Model # TBD

• Avion Deipo latches for fridge/freezer drawers and lower freezer unit in laundry area

Main Salon/ Helm Station

• Flooring: Solid 2″ (5.08cm) wide teak planking

• Cabinetry/paneling: Teak with 60% gloss varnish

• Dinette table: Teak with Teak base. Finish to be a 60% gloss varnish

• Coffee table: hinged top with storage below. Top to have a 60% gloss finish

• Furniture: Settee port side as designed with all detail as shown in layout drawing — to be teak veneer with solid teak trim. Coffee table

• Overhead: Individual padded Majilite panels secured in place using the FastMount system for easy removal and reinstallation

• Locker interior finish: 60% gloss varnished teak

• Cushions with upholstery TBD

• Teak valance over windows

• Free standing lounge chair

• Raised Helm seat with storage drawers under.

• Raised pilothouse floor at helm

• Mullions for window treatment for all side windows

• Include OceanAir Skysol Classic manual blinds, fabric choices from OceanAir Skysol Group 3

Master Cabin

• Floors: Carpet

• Cabinetry/paneling: Teak with 60% gloss varnish

• Overhead: Individual padded Majilite panels secured in place using the FastMount system for easy removal and reinstallation

• Locker interior finish: 60% gloss varnished teak

• Mattress: 6″ thick Foam with cotton mattress ticking

• Hull staving to be painted a matching color to the overhead

• Fresh air intake blower 24v

• Include OceanAir Skysol Classic manual blinds, fabric choices from OceanAir Skysol Group 3

Heads

• Floors: Tile

• Countertops: Formica brand solid surface ‘Frost’ #103 – 1 1/2″ thick at edges squared edge detail with 3/4″ overlap to cabinet face below

• Mirrors with 60% gloss varnished teak frames

• Shower floor: Molded fiberglass with non-skid finish

• Overhead: Individual gloss white FRP panels secured in place using the FastMount system for easy removal and reinstallation

• Cabinetry/paneling: Teak with 60% gloss varnish

• Locker interior finish: White Formica

• Shower door to be frameless clear glass with polished stainless steel hardware

• TP and towel bars as per drawing

• Exhaust blower 24vdc

• Forepeak/Chain locker

• Painted with white gel coat

• Drain to bilge through a PVC pipe installed during hull lamination

• Shelf with high fiddle on port side of chain locker for secondary anchor rode

• Access via gasketed door at fwd bulkhead of fwd guest cabin

• 24 volt dome light

Laundry

• Bosch washer – WAS 24460

• Bosch dryer – WTV 7610US

• Freezer – U-Line model # 75FWH-13 with Avion Deipo latch and teak door panel

• Cabinetry/joiner work: Satin varnished teak

• Floors: Solid 2″ (5.08cm) wide teak planking

• Teak doors over washer and dryer lockers

Guest cabins x 2

• Floors: Carpet

• Cabinetry/paneling: Teak with 60% gloss varnish

• Overhead: Individual padded Majilite panels secured in place using the FastMount system for easy removal and reinstallation

• Locker interior finish: 60% gloss varnished teak

• Mattresses: 6″ thick Foam with cotton mattress ticking

• Hull staving to be painted white

• Fresh air intake blower 24vdc

• Include OceanAir Skysol Classic manual blinds, fabric choices from OceanAir Skysol Group 3

Lighting

• Main overhead lighting throughout: Imtra LED “Ventura-HS” Square bezel stainless steel finish model no. #ILIM30471 with wall switches for each designated area. (Approx. 58 lights)

• Bulkhead reading lights: Imtra “Sidney” with switch Chrome finish model no. #ILIM40501- two (2) for guest stateroom and two (2) for salon

• Engine room lights: AC fluorescent – Three (3) x 24″ (70 cm) dual fluorescent (#ILMUL2-24T5HPF1) switch at entrance to engine room. Six (6) 24 volt dome lights in engine room

• Exterior overhead lights: Imtra LED “Ventura” cool white, stainless steel finish model no. #ILIM30411 x 6, 4 on aft deck and 2 under arch on F/B

• Navigation lights: Hella “NaviLED” in black, 3nm color reg, Mast Head, Stern, Port and Starboard side. Anchor light to be NaviLED horizontal mount #2LT 980 910-011 2nm.

• Owners cabin reading lights Imtra “Izar”(single arm) chrome model no. #IFLS31157042.C. (2 total) with two (2) ivory color shades No. #ILFSPAR.223.A

• Courtesy lights Imtra “Circinus-QB” Chrome Model no. #ILFS5570. at stairs to lower levels, One in each head and two in galley approx. (26) total

• Forward guest cabin reading lights Imtra “Izar”(single arm) chrome model no. #IFLS31157042.C. (2 total) with two (2) ivory color shades No. #ILFSPAR.223.A

• Exterior courtesy lights Imtra “Yukon” cool white LED model no. #ILIM70611 Qty. Approx. 21

• Hanging locker lights Imtra “Resolux 805” model no. #IL6262 with micro switch for auto on-off x five (5)

• Interior handrails shown on drawing to be included. All rails to be stainless steel unless noted differently.

• All drawers to have BLUM “Tandem” concealed self closing drawer slides

• All locker doors to have BLUM self closing hinges or equivalent